Hiển thị các bài đăng có nhãn Canon Pixma. Hiển thị tất cả bài đăng
Hiển thị các bài đăng có nhãn Canon Pixma. Hiển thị tất cả bài đăng

Thứ Bảy, 12 tháng 11, 2016

How to solve error E21 or E,2,1 on Canon MP495, MP499 printers

Résoudre l'erreur E21 ou E,2,1 sur les imprimantes Canon MP495, MP499

The error code E21 or E,2,1 means there is a timeout error occurred during WPS push button setup, on Canon Pixma MP495, MP499 printers.


Solution 1:
  • Press the Color button
  • Try the WPS setup again.

Solution 2:

Thứ Hai, 17 tháng 10, 2016

Thứ Ba, 24 tháng 6, 2014

How to solve error B300 on Canon printers


Error code B300 concerns these Canon printers: MP7600, IX7000, MX7600...
Sometimes there is a message like "cancel printing, shut down the power and try again. If it doesn't work, call Canon service".

Alarm and power leds blink 8 times. Error B300 is a reactor error: a hardware error in supply of the ractor liquid


Solutions 1:
  • Power off the printer.
  • Disconnect the power cord from the electrical outlet.
  • Hold down the power button and Wait one minute.
  • Reconnect the power cord to the electrical outlet.
  • Switch on the printer.


Solution 2:
  • Power off the printer.
  • Disconnect the power cord from the electrical outlet
  • Wait for ten minutes.
  • Reconnect the power cord to the electrical outlet.
  • Switch on the printer.


Solution 3:
  • Clean the ink cartridges contacts.

Solution 4:
  • Open the printer and wait for the carriage to slide over.
  • Remove the ink cartridges.
  • Clean the print head with cotton swabs dipped in hot water.
  • Once finished, allow to dry the printhead.
  • Replace the cartridges



Solution 5:
  • Replace the valve unit

Solution 6:
  • Replace the sheet feed unit


Links:
  • QY6-0066: Printhead Canon for  IX7000, MX7600, MP7600
  • QM3-5358: Sheet feed unit IX7000
  • QM3-1948: Sheet feed unit MX7600
  • QM3-5339: RCT Pump Valve

Thứ Ba, 13 tháng 5, 2014

Ten flashes with Canon Pixma IP4950


When the printer Canon IP4950 flashes ten times, it means it cannot perform duplex printing.

The size of paper may not be compatible with automatic duplex printing.

The sizes of media suitable for auto duplex printing are A4, Letter, A5, and B5.


Solution:
  • Make sure that the size of the paper loaded in the printer is correct. 
  • Press the "Resume/Cancel" button to eject the paper and restart printing from the front side of the next paper. 
  • The reverse side of the ejected sheet will not be printed.

Thứ Ba, 25 tháng 2, 2014

Error 9100 on Canon Pixma Pro9000 and Pro9500

Orange led (Alarm LED) and green led (Power LED) blink 10 times and you have an error code 9100, 9200 or 9201.

This is a carriage board error.


Solution 1:
  • Power off the printer
  • Unplug the power cord.
  • Wait for an hour
  • Plug in the power cord.
  • Switch on the printer

Solution 2: a part is defective; you have to replace:
  • Carriage unit (QM2-2967)
    Logic board ass'y (QM2-3180)

Thứ Tư, 23 tháng 1, 2013

How to solve Error Code 6A00 on Canon Pixma printers


Error code 6A00 is a Canon generic code for paper path jam.


Solution 1:
  • Move the printhead carriage back and forth a few times.

Solution 2:
  • Check the purge unit: Moving the print head assembly will not clear a purge unit if its jammed with paper, paper clips, push pins, screws, cookie crisp, flower bud pods or the like.

Solution 3:
  • Press the ink pads down in the purge unit.

Error 5100 on Canon printers

 MAJ 17/09/14

Error 5100 appears on these Canon printers: MP140, MP150, MP160, MP190, MP210, MP220,  MP800, MP810, MP170, MP180, MP450, MP460, MP830, MP970, MP980, MP240, MP250, MP260, MP270, MP480, MP500, MP510, MP520, MP530, MP540, MP620, MP550, MP560, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100, MP640, MP990, MG5200, MG5300, MG6100, MG6200, MG8100, MG8200

It's a Carriage error.

Solution 1:
  • Look inside for a tiny object like a piece of paper, a staple...

Solution 2:
  • The purge cap (the white sliding mechanism that the print head parks to when it's not in use) may be not lubricated well enough . Lubricate the sliders with some white grease (don't get it on the small wipers or the black caps); this repair probably require to remove the right panel off of the printer to gain access to the purge mechanism.

Solution 3:
  • Clean the timing strip: there is a thin plastic strip running across the width in front of and below the drive belt: there are fine black vertical lines on this strip. If the strip gets a piece of crud on it, you get an error during the start-up sequence.Gently clean this strip with a damp lint-free tissue.
  • photo: 
(you can see a transparent horizontal strip object which controls the movement of the printer head slots.)


Error code list by brand

    Thứ Ba, 13 tháng 11, 2012

    How to reset waste ink pad on Canon Pixma MP280

    Error P07 means the waste ink counter is full.

    Solution 1:
    1. First, search and download the Service Tool V1074.

    • Turn off the printer
    • Hold down the "stop/reset" and press the "power" button without release it.
    • Release the "stop/reset".
    • Press the "stop/reset" button six times and release the two buttons.
    • The printer is now in service mode.
    • Extract the Service tool and the file to open service tool page
    • Find the "clear ink counter" section and click on the "main" button.
    • Scroll down to find "ink absorber counter" on the left and to the right of that "counter value".
    • Ink absorber counter box should read "main" and counter value reads "0".
    • Click the set button to the right of the counter value box.
    • The printer will now make some noise and will print a page of paper,.
    • A message will tell you when the process has been completed.
    • Click on the prompts.
    • Turn the printer off wait a few seconds and turn it back.

    Solution 2:
    • Unplug power and USB cable.
    • Open door and hold power button.
    • Connect power.
    • Close door, then release power button.  

    Solution 3:

        Thứ Sáu, 21 tháng 9, 2012

        Canon Pixma MP495 printer

        Canon Pixma MP495 printer
        MAJ15/12/16
        Downloads:

        Cartridges:
        • PG-210: Black Ink
        • PG210XL: Back ink XL
        • CL-211: Color ink
        • CL211XL: Colour Ink XL

          Troubleshooting:
          • Waste ink counter Reset (error E08):
          Service tool V3400 for resetting Canon printers counter
          • Ink cartridge reset (ship reset):
          Solution 1 : When "empty cartridge" is displayed, Hold on the "cancel" button until "processing"appears.
          Solution 2: Hold on the "Stop" button until "processing" appears

          • Error E16 or E,1,6:
          Hold on the "Stop" button for 5 seconds.